What's Covered on This Page

• Reasons Electric Gates Fail
• When to Call a Professional Instead of Trying Again
• Coastal Climates and Community Association Gates Require Unique Repair Solutions
• How does Hallandale Beach's salt air affect my electric gate system?
• What should I do if my gate stops working after a storm?
• How long does a typical electric gate repair visit take?
• What happens if I ignore a gate that's making grinding noises?
• Will the technician be able to fix my gate on the first visit?
• Are electric gates in Hallandale Beach required to have safety sensors working correctly?

Need Electric Gate Repair Service?

9547152716

Call Today For A Free Estimate

Reasons Electric Gates Fail

You push the button on your gate remote, then try again. You get out of the car, walk up, and press the wall button. Nothing happens. This is when most folks in Hallandale Beach, FL, call us for electric gate repair service.

And it's one of those handful of issues that comes up every week.

South Florida weather wreaks havoc on gate systems. Salt air eats away at wire connections. Afternoon storms send voltage spikes through the controls. And humidity alone can short-circuit sensors that were just fine yesterday. Your gate doesn't have to be old to act up. It just needs to sit out here.

Below are some of the common reasons we find gates stuck in the open or closed position:

• Weak or dead motor from age, heat, and everyday use
• Corroded wires in wire connections at ground-level junctions or in gate posts
• Sensor misalignment, causing the gate to think it's blocked
• Bad control board from lightning strikes or power outages
• Bad rollers or hinges that put too much stress on the gate opener

Some of these can be repaired right away. A bumped sensor can be realigned in moments. A bad control board is a different situation entirely.

How Things Get Worse

Delay. We get that feeling when you wait on a repair. A small wire problem can become a total motor replacement when the system is forced repeatedly against resistance. We see this a lot in Golden Isles, where older gates are used all the time. The residents may hear grinding, let it go for a couple weeks, and then open the gate one morning and it will stay still.

Adding to the problem is troubleshooting. Replacing a gate remote battery is acceptable. But opening the control box and not knowing what you're doing can lead to major trouble. According to the Consumer Product Safety Commission, automated gates cause hundreds of injuries each year due to malfunctioning safety features.

And if your gate is already misbehaving, don't wait for it to break completely. An inexpensive repair now will save you from a costly headache down the road.

When to Call a Professional Instead of Trying Again

Let's be honest. Your gate won't work and you first thing you do is try the remote a few more times. Maybe you reset the breaker box. Sometimes, it really does work.

Other times, though, it won't.

There's a difference between a glitch that passes after a bit and something that gets worse as the gate moves. We run into this on a weekly basis in Hallandale Beach. People wait too long for an issue to resolve itself. Here is what we usually look for to determine whether your gate needs an expert electric gate repair service in Hallandale Beach:

• It opens but doesn't close all the way. Most of the time, that is sensor misalignment or a motor issue, not a dead battery in the remote.
• You hear grinding or scraping. Metal-on-metal is almost always a track shift or worn rollers.
• It's getting slower. A motor under load will fail quickly if it keeps running slow.
• The keypad or intercom still works, but the gate ignores them. That is a control board issue.
• You see rust, bent rails, or cracked welds. Salt air in places like Golden Isles is particularly hard on gate hardware.

If you experience any one of these, the issue is almost always mechanical or electrical. No reprogramming will fix a worn gear or a frayed wire. And leaving that untreated will turn a minor gate repair into a full motor replacement. Here's a good example of this issue that we commonly encounter with electric gates. A homeowner notices that their sliding gate will pause halfway, before slowly completing the close. He or she decides to put up with it for a few weeks. By the time they finally reach out to us, the chain is worn and the drive has been severely damaged. The minor adjustment that would have saved time and money has now become a much bigger and more costly job.

Is the issue serious? Do you think you just have minor electric gate repairs that need to be done? This is a common problem that we can help you with, as the majority of people cannot tell the difference. As a licensed contractor working across Hallandale Beach, we can diagnose the issue within no time.

What happens once I contact you for electric gate repairs?

You called us and we are on the way. Great! What now? When a technician from our company arrives at your Hallandale Beach home or business, you can expect us to ask the necessary questions first. However, all electric gate repair visits are typically identical in nature.

A complete inspection. We check the motor, the control board, the track (hinged or sliding), safety sensors, and wiring. The remotes. We even examine the gate's outer perimeter for things you can't see from your house, like contact corrosion or a nearly broken chain. During a typical electric gate repair visit, we will:

• Conduct a visual inspection of the gate.
• Power-on-test the opener and listen for unusual sounds such as clicking or grinding.
• Open the control board to inspect fuses and wire connections.
• Check the track or hinge alignment.
• Perform a test cycle, verifying the complete open and close operations and safety sensor responses. This includes verifying that entrapment protection devices work as required by UL 325 safety standards for gates.
• We clearly tell you what the issue is and what must be done to resolve it. No speculation.

We can do the repair immediately. We keep most parts in our vans because waiting around in South Florida for a gate part several days is not an option. The gate is then wide open, inviting any kind of threat into your home. Your house could be located on Three Islands, or close to the Diplomat neighborhood and this is not something that you can allow to happen.

If the damage is too bad to repair, we will inform you promptly. We've been doing this sort of work long enough to know when to replace a part and when not to, so you won't end up having to replace that part again in a few months. We are fully licensed and insured, which means that whatever we install is in compliance with code.

The average time to complete an electric gate repair in Hallandale Beach is less than two hours. No special preparation is required from you. All we need is access to the gate, and to the power. We take care of the rest.

Watch Our Video

See How We Handle Electric Gate Repair Service in

On Time Garage Door Repair

Coastal Climates and Community Association Gates Require Unique Repair Solutions

Sea air corrodes metal. It's not hyperbole, it's reality for those living along the coastline.

Hallandale Beach is located directly next to the coast, and the salty air corrodes gate tracks, hinges, chains and circuit boards in far less time than one would think. We have inspected operators at several properties in or near Golden Isles, and found green corrosion caked onto two-year-old wiring inside the operator box. That same equipment could be expected to last 5-6 years without issue in a more inland community, but that's not the case here. According to the Federal Highway Administration, chloride exposure is one of the top causes of metal degradation in infrastructure. Your gate experiences this same exposure every day of the year.

So, our electric gate repair solutions have to work in that environment, instead of just repairing the issue at hand. When providing gate repair services on a residential property in Hallandale Beach, we look for several things most companies don't:

• Corrosion inside the operator box and on the relay contacts
• Friction and rust build-up along steel tracks and roller brackets
• Moisture damage to safety sensors and control boards
• Fractured or weakened welds on gate frames from constant salt exposure

Then, there is the association gates in Hallandale Beach. Those gates experience a wear-and-tear that residential ones do not. We're looking at hundreds of open-close cycles a day. Couriers, homeowners, guests, contractors. All that adds up and wears out motors, gears and loop detection devices very quickly. Installing an HOA gate is a whole different ball game from maintaining it.

Why Association Gate Repair Is More Complicated

Association boards require paperwork. They want to know: what broke, why it broke, and what did we do to make sure it didn't break again? We totally get that. We repair gates for HOAs and other property owners in Hallandale Beach on a constant basis. The board just needs to know the gate is fixed and won't keep breaking within months. Due to the heavy use and climate in Hallandale Beach, gates need repairs with quality parts. We don't make temporary fixes that fail in six months, we make long-term repairs.

Repair vs Replacement, Which Should You Choose?

This is probably the most asked question we hear from our Hallandale Beach gate repair customers. There's no easy answer. Here's the general rule we give to all our customers in Hallandale Beach: If your gate system is under 10 years old and the frame is good, repair. Motors and circuit boards wear out, rollers break, and that's fine. But a worn limit switch doesn't mean your gate is done. The opposite also exists, there are certain times when repair does make more sense. Before you make that call, consider a few things: How often you've needed electric gate repair service in the last two years? Is the frame of the gate in good condition or is it rotted, bent, or damaged? Does the manufacturer of the motor still offer parts to repair your current gate? Does your current gate system meet your security needs?

I hear this almost every week: "my gate in the Golden Isles broke and is going to need repair or replacement". In 90 percent of those cases, we can repair the gate without the need to install a whole new motor system. Often the limit switch just needs replaced. This only takes a few minutes to resolve.

When Replacement Makes Sense

But the opposite is true as well. When the gate has needed to be fixed several times in the last year, you're better off with new gate operators. You're going to have more problems later with a rusted frame regardless of how much you're willing to pay someone to keep it aligned, and when a gate's track has slowly shifted in all the years of building in Hallandale Beach's sandy soil, it may take multiple repairs in the future to keep it running smoothly. How do you know which situation you're in? Our gate inspection is designed to give you a straight answer on what your gate system needs so you can make an informed decision on the choice for your situation. We've been doing this work for so long, we can tell you if we can fix your problem, but if we can't, we'll tell you why, and help guide you on options for new gate installations, whether it be for a sliding driveway or swing driveway. If you have any questions about where your gate is, give us a call.

Frequently Asked Questions

Common questions about Electric Gate Repair Service

Ready to Get Started?

Call 9547152716 Today For A Free Estimate.